Updates & Revisions

Here you will find important updates and revisions to the articles and plans published in Woodsmith magazine.

Woodsmith Issue 176 cover image

April 2008
Issue 176

Charging Station
Page 20: Materials, Supplies & Cutting Diagram
Parts B, C and D should all be 11" in length, not 10 3/4" as originally printed. The correct measurement is shown in the drawings throughout the article.
Page 20: Main Illustration
The support panel (part G) is 4 5/8" high, as listed in the material cutting diagram.
Page 20: Materials, Supplies & Cutting Diagram
The second part E shown in the cutting diagram should be labeled part H and should be listed as (.3 bd. ft.) not square feet since it is 3/4"-thick material. Also, graphically, since both part E's are 4" x 12", the two boards should both look the same size in the diagram.
Charging Station
Page 20: Materials, Supplies & Cutting Diagram
Parts B, C and D should all be 11" in length, not 10 3/4" as originally printed. The correct measurement is shown in the drawings throughout the article.
Page 20: Main Illustration
The support panel (part G) is 4 5/8" high, as listed in the material cutting diagram.
Page 20: Materials, Supplies & Cutting Diagram
The second part E shown in the cutting diagram should be labeled part H and should be listed as (.3 bd. ft.) not square feet since it is 3/4"-thick material. Also, graphically, since both part E's are 4" x 12", the two boards should both look the same size in the diagram.
Charging Station
Page 20: Materials, Supplies & Cutting Diagram
Parts B, C and D should all be 11" in length, not 10 3/4" as originally printed. The correct measurement is shown in the drawings throughout the article.
Page 20: Main Illustration
The support panel (part G) is 4 5/8" high, as listed in the material cutting diagram.
Page 20: Materials, Supplies & Cutting Diagram
The second part E shown in the cutting diagram should be labeled part H and should be listed as (.3 bd. ft.) not square feet since it is 3/4"-thick material. Also, graphically, since both part E's are 4" x 12", the two boards should both look the same size in the diagram.
Classic Oak Wine Server
Page 35: References to the bevel angle
The text and the illustration of the bevel give a blade tilt angle of 30 degrees; this is too steep. The angle should be about 18 degrees.
Page 34: Detail A
The measurement at the top of the detail for placement of the magnet should be 4 1/4" from the notched edge of the front stretcher. Note: The measurement is correct as shown in the drawing on page 32.
Page 32: Detail B
The spacing between the predrilled screwholes was not correctly illustrated: The first screw should be 7/8" from the edge. The next space should be 3 7/8" from the first screw. Then there should be three spaces of 4" each. Finally the 3 7/8" repeats and then another 7/8" at the end.
Page 51: Hardware source
The source for the pivot hinges was omitted. Lee Valley sells the Steel Pivot Hinge, part number 00H03.11.
Page 32: Detail 'a'
The hole for the "pivot hinge cup" is called out as 7/64". It should be 17/64"
Page 37: Detail 'a'
The arrow for the lowest part labeled 'Q' should be extended to point to the next item (Wine Rack Shelf) above the bottom shelf, not the bottom shelf as illustrated.
Classic Oak Wine Server
Page 35: References to the bevel angle
The text and the illustration of the bevel give a blade tilt angle of 30 degrees; this is too steep. The angle should be about 18 degrees.
Page 34: Detail A
The measurement at the top of the detail for placement of the magnet should be 4 1/4" from the notched edge of the front stretcher. Note: The measurement is correct as shown in the drawing on page 32.
Page 32: Detail B
The spacing between the predrilled screwholes was not correctly illustrated: The first screw should be 7/8" from the edge. The next space should be 3 7/8" from the first screw. Then there should be three spaces of 4" each. Finally the 3 7/8" repeats and then another 7/8" at the end.
Page 51: Hardware source
The source for the pivot hinges was omitted. Lee Valley sells the Steel Pivot Hinge, part number 00H03.11.
Page 32: Detail 'a'
The hole for the "pivot hinge cup" is called out as 7/64". It should be 17/64"
Page 37: Detail 'a'
The arrow for the lowest part labeled 'Q' should be extended to point to the next item (Wine Rack Shelf) above the bottom shelf, not the bottom shelf as illustrated.
Classic Oak Wine Server
Page 35: References to the bevel angle
The text and the illustration of the bevel give a blade tilt angle of 30 degrees; this is too steep. The angle should be about 18 degrees.
Page 34: Detail A
The measurement at the top of the detail for placement of the magnet should be 4 1/4" from the notched edge of the front stretcher. Note: The measurement is correct as shown in the drawing on page 32.
Page 32: Detail B
The spacing between the predrilled screwholes was not correctly illustrated: The first screw should be 7/8" from the edge. The next space should be 3 7/8" from the first screw. Then there should be three spaces of 4" each. Finally the 3 7/8" repeats and then another 7/8" at the end.
Page 51: Hardware source
The source for the pivot hinges was omitted. Lee Valley sells the Steel Pivot Hinge, part number 00H03.11.
Page 32: Detail 'a'
The hole for the "pivot hinge cup" is called out as 7/64". It should be 17/64"
Page 37: Detail 'a'
The arrow for the lowest part labeled 'Q' should be extended to point to the next item (Wine Rack Shelf) above the bottom shelf, not the bottom shelf as illustrated.
Classic Oak Wine Server
Page 35: References to the bevel angle
The text and the illustration of the bevel give a blade tilt angle of 30 degrees; this is too steep. The angle should be about 18 degrees.
Page 34: Detail A
The measurement at the top of the detail for placement of the magnet should be 4 1/4" from the notched edge of the front stretcher. Note: The measurement is correct as shown in the drawing on page 32.
Page 32: Detail B
The spacing between the predrilled screwholes was not correctly illustrated: The first screw should be 7/8" from the edge. The next space should be 3 7/8" from the first screw. Then there should be three spaces of 4" each. Finally the 3 7/8" repeats and then another 7/8" at the end.
Page 51: Hardware source
The source for the pivot hinges was omitted. Lee Valley sells the Steel Pivot Hinge, part number 00H03.11.
Page 32: Detail 'a'
The hole for the "pivot hinge cup" is called out as 7/64". It should be 17/64"
Page 37: Detail 'a'
The arrow for the lowest part labeled 'Q' should be extended to point to the next item (Wine Rack Shelf) above the bottom shelf, not the bottom shelf as illustrated.
Classic Oak Wine Server
Page 35: References to the bevel angle
The text and the illustration of the bevel give a blade tilt angle of 30 degrees; this is too steep. The angle should be about 18 degrees.
Page 34: Detail A
The measurement at the top of the detail for placement of the magnet should be 4 1/4" from the notched edge of the front stretcher. Note: The measurement is correct as shown in the drawing on page 32.
Page 32: Detail B
The spacing between the predrilled screwholes was not correctly illustrated: The first screw should be 7/8" from the edge. The next space should be 3 7/8" from the first screw. Then there should be three spaces of 4" each. Finally the 3 7/8" repeats and then another 7/8" at the end.
Page 51: Hardware source
The source for the pivot hinges was omitted. Lee Valley sells the Steel Pivot Hinge, part number 00H03.11.
Page 32: Detail 'a'
The hole for the "pivot hinge cup" is called out as 7/64". It should be 17/64"
Page 37: Detail 'a'
The arrow for the lowest part labeled 'Q' should be extended to point to the next item (Wine Rack Shelf) above the bottom shelf, not the bottom shelf as illustrated.
Classic Oak Wine Server
Page 35: References to the bevel angle
The text and the illustration of the bevel give a blade tilt angle of 30 degrees; this is too steep. The angle should be about 18 degrees.
Page 34: Detail A
The measurement at the top of the detail for placement of the magnet should be 4 1/4" from the notched edge of the front stretcher. Note: The measurement is correct as shown in the drawing on page 32.
Page 32: Detail B
The spacing between the predrilled screwholes was not correctly illustrated: The first screw should be 7/8" from the edge. The next space should be 3 7/8" from the first screw. Then there should be three spaces of 4" each. Finally the 3 7/8" repeats and then another 7/8" at the end.
Page 51: Hardware source
The source for the pivot hinges was omitted. Lee Valley sells the Steel Pivot Hinge, part number 00H03.11.
Page 32: Detail 'a'
The hole for the "pivot hinge cup" is called out as 7/64". It should be 17/64"
Page 37: Detail 'a'
The arrow for the lowest part labeled 'Q' should be extended to point to the next item (Wine Rack Shelf) above the bottom shelf, not the bottom shelf as illustrated.